7-inch colored display; all basic and enhanced functionalities including automatic measurements, advanced triggering modes, record length; high-performance oscilloscope designed for a range of high-end debugging applications including R&D, circuit design, quality control, manufacturing in electronics and communications or other industries.

Main Index And Parameters:

Bandwidth：25MHz

Real-time Sample Rate：250MSa/s

Equivalent Sample Rate： None

Record Length(Sample Points) ：4K

SEC/DIV Range：4nS/div-40S/div (in a 2, 4, 8 sequence)

Delay Time Accuracy：500ps

Vertical：

A/D Converter：     8-bit resolution, each channel sampled simultaneously

VOLTS/DIV Range： 2mV/div～5V/div at input BNC

Position Range：    ±50V(5V/div),±40V(2V/div～500mV/div),2V(200mV/div～50mV/div)±400mV(20mV/div～2mV/div)

Bandwidth Limit：   None

Rise Time at BNC：  ≤ 14ns

DC Gain Accuracy： ±4% for Sample or Average acquisition mode, 5mV/div to 2mV/div

±3% for Sample or Average acquisition mode, 5V/div to 10mV/div

Trigger：

"Trigger Sensitivity(Edge Trigger Type)" ：DC:     CH1/CH2(Typical)   1div from DC to 10MHz;1.5div from 10MHz to Full

                                             EXT（Typical）     200mV from DC to 40MHz

                                             EXT/5（Typical）   1V from DC to 40MHz

                                    AC:     Attenuates signals below 10Hz

                                     HF Reject:      Attenuates signals above 80kHz

                                    LF Reject:      Attenuates signals below 150kHz

                                    Noise Reject:   Reduces trigger sensitivity

Trigger Level Range： CH1,CH2:  ±8 divisions from center of screen

EXT:      ±1.2V      EXT/5: ±6V

"Trigger Level Accuracy,typical (Accuracy is for signals having rise and fall times ≥20ns)" ：

CH1,CH2: ±(0.3div×V/div) (within ±4 divisions from center of screen)

EXT: ±(6% of setting + 40mV)

EXT/5: ±(6% of setting + 200mV)

Holdoff Range:      100ns-10s

Trigger Type:

Edge:          Trigger on the rising or falling edge

Pulse Width:    Trigger (when >,<,=,≠) on positive or negative pulses   Pulse Width Range: 20ns-10s

Video:         Trigger on an NTSC, PAL, or SECAM standard video signal   Line Range: 1-525 (NTSC), 1-625 (PAL/SECAM)

Slope:         None

Overtime:      None

Alternate:      None

Measurement:

Cursors:  Manual: The difference between voltage cursors △V; the difference between time cursors △T; 1/△T calculated by Hz.  

Tracing: The voltage and time at a waveform point

Automatic: Pk-Pk, Max, Min, Mean, Cyc RMS, Frequency, Period, Rise Time, Fall Time, Positive Width, Negative Width

Display:

Type: Right angle 7"TFT 16-digit color LCD

Resolution: 800*480 dots

Contrast: 16 gears, with the progress bar to show adjustment

Interface: USB host and USB slave

Main Index And Parameters:

Bandwidth：25MHz

Real-time Sample Rate：250MSa/s

Equivalent Sample Rate： None

Record Length(Sample Points) ：4K

SEC/DIV Range：4nS/div-40S/div (in a 2, 4, 8 sequence)

Delay Time Accuracy：500ps

Vertical：

A/D Converter：     8-bit resolution, each channel sampled simultaneously

VOLTS/DIV Range： 2mV/div～5V/div at input BNC

Position Range：    ±50V(5V/div),±40V(2V/div～500mV/div),2V(200mV/div～50mV/div)±400mV(20mV/div～2mV/div)

Bandwidth Limit：   None

Rise Time at BNC：  ≤ 14ns

DC Gain Accuracy： ±4% for Sample or Average acquisition mode, 5mV/div to 2mV/div

±3% for Sample or Average acquisition mode, 5V/div to 10mV/div

Trigger：

"Trigger Sensitivity(Edge Trigger Type)" ：DC:     CH1/CH2(Typical)   1div from DC to 10MHz;1.5div from 10MHz to Full

                                             EXT（Typical）     200mV from DC to 40MHz

                                             EXT/5（Typical）   1V from DC to 40MHz

                                    AC:     Attenuates signals below 10Hz

                                     HF Reject:      Attenuates signals above 80kHz

                                    LF Reject:      Attenuates signals below 150kHz

                                    Noise Reject:   Reduces trigger sensitivity

Trigger Level Range： CH1,CH2:  ±8 divisions from center of screen

EXT:      ±1.2V      EXT/5: ±6V

"Trigger Level Accuracy,typical (Accuracy is for signals having rise and fall times ≥20ns)" ：

CH1,CH2: ±(0.3div×V/div) (within ±4 divisions from center of screen)

EXT: ±(6% of setting + 40mV)

EXT/5: ±(6% of setting + 200mV)

Holdoff Range:      100ns-10s

Trigger Type:

Edge:          Trigger on the rising or falling edge

Pulse Width:    Trigger (when >,<,=,≠) on positive or negative pulses   Pulse Width Range: 20ns-10s

Video:         Trigger on an NTSC, PAL, or SECAM standard video signal   Line Range: 1-525 (NTSC), 1-625 (PAL/SECAM)

Slope:         None

Overtime:      None

Alternate:      None

Measurement

Cursors:  Manual: The difference between voltage cursors △V; the difference between time cursors △T; 1/△T calculated by Hz.  

Tracing: The voltage and time at a waveform point

Automatic: Pk-Pk, Max, Min, Mean, Cyc RMS, Frequency, Period, Rise Time, Fall Time, Positive Width, Negative Width

Display

Type: Right angle 7"TFT 16-digit color LCD

Resolution: 800*480 dots

Contrast: 16 gears, with the progress bar to show adjustment

Interface: USB host and USB slave